Secure Pendant

Menu

Secure Pendant

Level
Confident Beginner
Session
1 hour session, on-line
Description
This is the forth project in the Step by Step Surprise series. Every project has had its own flare, while this one will sparkle. To participate register at The Urban Beader.

Tools

Tools required to complete project.
  • Bench Block

    Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
  • Bench Pin

    There are a variety of bench pins available on the market, any will do. However, you will need to bring a 4” or larger C-clamp. As the C-clamp provided with a bench pin does not fit most tables at the shows. 
  • Tool C-clamp

    C-clamp

    To be used with bench pins to clamp to tables. May be found at any local hardware store. Must be at least 3 inches. 
  • Cut Lube

    Used to lubricate saw blades and drill bits for ease of cutting.
  • Tool Flex Shaft

    Flex shaft

    Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited. 
  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       
  • Heavy Duty Cutters

    Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.
  • Tool Horned Anvil

    Horned Anvil

    For most classes using this anvil, the key is in the square side. We will use to assist in the forging of the shape.
  • Jeweler’s Saw

    Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Muslin buffing wheels

    Used with a flex shaft or Dremel to polish metal.
  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
  • Rawhide/Leather Mallet

    Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.
  • Ring Mandrel, Steel

    Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.
  • Ring Sizer

    Optional, used to measure your ring size. Several sets will be provided to share in class.
  • Tool Round File

    Round File

    Used to file curved areas. Round files are gradually tapered, cut and workable to the point. Used where it is necessary to enlarge a hole or round off a radius.
  • Soldering Kit

    (Optional) 
    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.

  • Student Files

    Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
  • Tube Cutting Pliers

    A great gadget to aid in cutting tubes. These pliers create even leverage on the tube for sawing. Provided for all classes with tubes.
Facebook Twitter Pinterest