Whirly Petal Ring

Menu

Whirly Petal Ring

Level
Intermediate
Session
4 hours
Description
Why do we make kinetic jewelry? Because we can! In this class, I will demystify the soldering steps of this multi-layered project with a different approach and how to keep pieces moving. In the end, each piece will whirl independently.

Tools

Some tools will be provided by the instructor. Please refer to your registration.

  • Bench Block

    Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
  • Tool Broach

    Broach

    A five-sided tapered file of sorts used to clear the inside of a tube.
  • Tool Circle Template

    Circle Template

    Used to create a pattern for cutting. For most classes this template needs to include circles at least 1.25" in diameter or larger. 

  • Cut Lube

    Used to lubricate saw blades and drill bits for ease of cutting.
  • Tool Disc Cutter

    Disc Cutter

    Used to punch discs out of metals. One set will be provided to share in every class.

  • Fine Tweezers

    Used for moving small parts. Classes requiring fine tweezers will not work with fire tweezers. These are a cheap investment. Please be bring some. Optional for most classes.
  • Tool Flex Shaft

    Flex shaft

    Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited. 

  • Tool Tool Half Round Pliers

    Half round pliers are used to assist in bending wire to a circular form to reduce marring on the outside. Great for getting ring shanks started to making rings. In most classes, this is an optional tool. 

  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       

  • Helping Hand/Third Hand

    Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.

  • Tool Hollow Scraper

    Scrapers are used for smoothing cleaning and deburring metals.  Different from a burnisher, a hollow scraper removes the metal. In most classes, this is an optional tool.

  • Jeweler’s Saw

    Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Tool Metal Dap Set

    Metal Dap Set

    Used to dap metal to create a cup shape. 3 sets will be provided during classes to share. If you are bringing a set, please check with the instructor for needed sizes. Usually an entire set is needed for a class, only parts. This will lessen the weight you need to carry.

  • Needle File Set

    Used for filing smaller pieces of metal and tight places. When required, either diamond coated or fine tooth is preferred. Some students may prefer to use smaller files as opposed to the student files for their projects.
  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.

  • Rawhide/Leather Mallet

    Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.

  • Ring Mandrel, Steel

    Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.

  • Ring Sizer

    Optional, used to measure your ring size. Several sets will be provided to share in class.

  • Soldering Kit

    (Optional) 
    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.

Facebook Twitter Pinterest