Weave It To Metal

Menu

Weave It To Metal

Level
Beginner
Session
3 hours
Description
This isn't your high school basket weaving class. In this class, the challenge will be keeping it together. Your dexterity and attention to details will be put to the test. If you are ready for a challenge, join me for this class.

Tools

Some tools will be provided by the instructor. Please refer to your registration.
  • Bench Block

    Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
  • Tool Disc Cutter

    Disc Cutter

    Used to punch discs out of metals. One set will be provided to share in every class.
  • Tool Flex Shaft

    Flex shaft

    Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited. 
  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       
  • Helping Hand/Third Hand

    Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Muslin buffing wheels

    Used with a flex shaft or Dremel to polish metal.
  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
  • Rawhide/Leather Mallet

    Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.
  • Metal Ruler

    6" metal ruler is preferred unless otherwise noted. A larger one will also work, however, it may be a little cumbersome.
  • Side Cutters

    Also known as wire cutters or snippers. For many of my classes I prefer Ultra Flush side cutters because it eases the workload. Ultra flush is the most flush you can buy as opposed to just flush cutters. If you don't own a pair of Ultra Flush cutters, you may want to invest in a good pair either Lindstrom or Swanstrom. There is usually not a different in price between ultra and just flush cutters so why not just buy the best? The image shows just a side cutter (top) and ultra flush (bottom).
  • Soldering Kit

    (Optional) 
    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.

  • Student Files

    Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
  • Wood dap set

    Used to dap metal to create a convex/concave shape in metal.
Facebook Twitter Pinterest