Not Fools Gold

Not Fools Gold

Details

Level: Intermediate        Sessions: 1        Hours: 3 hours

Project Overview

Make 1, 2 or 3 rings using sterling silver and 10kt gold to create a contemporary ring. Students will gain experience creating anticlastic rings, soldering karat gold and small parts, and. Those who work quickly will finish a triple ring.
 

Tools

  • Bench Block (steel or anodized aluminum) - Used as a hammering surface for metal stamping or working with metal. 

  • Bezel Shears – Used to cut metal sheet. There are many available on the market, any of which will work, however they should NOT be serrated. (Tin snips or airplane shears will also work, however, they may be large and cumbersome.) If the project has curves in the design and you own a pair, bring curved bezel shears. This is an optional item for most classes. Shears will be provided for use during classes.  

  • Chasing hammer – Used for chasing/moving metal. In my classes chasing hammers are used to create hammer marks on metal and riveting. Instructor will provide for every class needed. 

  • Tool Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes. 
  • Heavy Duty Cutters – Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.

     

  • Helping Hand/Third Hand – Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.

  • Tool Magnifier or Optivisor

    Magnifier or Optivisor – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x. 

     

  • Tool Metal Dap Set

    Metal Dap Set – Used to dap metal to create a cup shape. 3 sets will be provided during classes to share. If you are bringing a set, please check with the instructor for needed sizes. Usually an entire set is needed for a class, only parts. This will lessen the weight you need to carry. 

  • Nylon nose pliers – Flat nose pliers with PVC grips o the heads. Mostly used for straightening wire. In my classes they are used to prevent marring when bending metal. Only required for some classes, but this is mostly an optional item. 

  • Tool Ott Light

    Ott Light or Task Lamp - This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision. 

  • Rawhide/Leather Mallet – Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.

  • Side Cutters - Also known as wire cutters or snippers.

    For many of my classes I prefer Ultra Flush side cutters because it eases the workload. Ultra flush is the most flush you can buy as opposed to just flush cutters. If you don't own a pair of Ultra Flush cutters, you may want to invest in a good pair either Lindstrom or Swanstrom. There is usually not a different in price between ultra and just flush cutters so why not just buy the best?

    The image shows just a side cutter (top) and ultra flush (bottom).

     

  • Optional Soldering Kit

    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements. 

  • Soldering Pick – A small, pointed instrument designed to help you move solder into place. 

  • Ring Mandrel, Steel – Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed. 

  • Student Files – Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.