Advanced

Boxed Up
Boxed Up

Level

Advanced

Session

6 hours, all day

Description

This fabricating class will touch on multiple skills that can be used to enhance any smithing project. Create a contemporary ring while refining your sawing, shaping and soldering techniques. Students will be encouraged to create their own designs. If you are looking for a challenge this class will surely impress. Every step will refine your skills and give you experience with that tool (saw) you have been avoiding.
Tools
Some tools will be provided by the instructor. Please refer to your registration.
- Bench Block
  Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
- Bench Pin
  There are a variety of bench pins available on the market, any will do. However, you will need to bring a 4” or larger C-clamp. As the C-clamp provided with a bench pin does not fit most tables at the shows.
- C-clamp
  To be used with bench pins to clamp to tables. May be found at any local hardware store. Must be at least 3 inches.
- Cut Lube
  Used to lubricate saw blades and drill bits for ease of cutting.
- Flex shaft
  Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited.
- Hand Tools
  
  Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.
  
  Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
  
  Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
  
  Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
- Heavy Duty Cutters
  Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.
- Horned Anvil
  For most classes using this anvil, the key is in the square side. We will use to assist in the forging of the shape.
- Jeweler’s Saw
  Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
- Magnifier or Optivisor
  – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.
- Muslin buffing wheels
  Used with a flex shaft or Dremel to polish metal.
- Ott Light or Task Lamp
  This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
- Rawhide/Leather Mallet
  Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubberone may not.
- Ring Mandrel, Steel
  Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.
- Ring Sizer
  Optional, used to measure your ring size. Several sets will be provided to share in class.
- Round File
  Used to file curved areas. Round files are gradually tapered, cut and workable to the point. Used where it is necessary to enlarge a hole or round off a radius.
- Soldering Kit
  
  (Optional)
  Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.
- Student Files
  Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
- Tube Cutting Pliers
  A great gadget to aid in cutting tubes. These pliers create even leverage on the tube for sawing. Provided for all classes with tubes.
Heavy Set
Heavy Set, bezel setting cut stones

Level

Advanced

Session

6 hours, all day

Description

Bezel setting just grew up. No longer reserved for bezel wire this setting will be constructed from heavy silver stock. From there we will work with a series of burs to create a seat to set the stone. You will need to bring steady hands for this project. Students will choose either a pendant or a ring to make.
Tools
Some tools will be provided by the instructor. Please refer to your registration.
- Ball Burnisher
  
  Used to burnish or smooth the surface of metal. For most projects using this tool you will want at least a 3mm ball. This tool may also be found at your local craft store for use with clay or nail art.
- Bench Block
  Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
- Bench Pin
  There are a variety of bench pins available on the market, any will do. However, you will need to bring a 4” or larger C-clamp. As the C-clamp provided with a bench pin does not fit most tables at the shows.
- Bezel Mandrel
  A small steel mandrel used to create round bezel settings, jump rings or other components.
- Bezel Pusher
  Not a tool I usually use, but from time to time they are helpful. Before using, consider sanding the edges of the tool to create a bevelled edge to reduce marring and scratches.
- C-clamp
  To be used with bench pins to clamp to tables. May be found at any local hardware store. Must be at least 3 inches.
- Curved Burnisher
  
  Used to burnish or smooth the surface of metal. For most projects using this tool you will want at least a 3mm ball. This tool may also be found at your local craft store for use with clay or nail art.
- Cut Lube
  Used to lubricate saw blades and drill bits for ease of cutting.
- Digital Caliper
  Why digital? It is more accurate. This is requested for advanced stone setting classes.
- Divider
  Used to score metal to create lines for cutting. May also be used to aid in measuring for consistency. A compass will NOT work, I already tried.
- Flex shaft
  Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited.
- Hand Tools
  
  Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.
  
  Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
  
  Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
  
  Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
- Heavy Duty Cutters
  Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.
- Helping Hand/Third Hand
  Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.
- Jeweler’s Saw
  Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
- Magnifier or Optivisor
  – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.
- Muslin buffing wheels
  Used with a flex shaft or Dremel to polish metal.
- Nylon nose parallel pliers
  – Parallel action provides even pressure while holding firm. I love using nylon parallel pliers to manipulate my metal. Parallel pliers were my favorite pliers until they made nylon nose parallel pliers. For almost all projects these pliers are optional. You may use regular nylon nose and parallel nylon nose interchangeably.
- Nylon nose pliers
  Flat nose pliers with PVC grips o the heads. Mostly used for straightening wire. In my classes they are used to prevent marring when bending metal. Only required for some classes, but this is mostly an optional item.
- Ott Light or Task Lamp
  This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
- Rawhide/Leather Mallet
  Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubberone may not.
- Ring Clamp
  Used to hold rings, but some like to use a ring clamp for holding metal when filing to save their hands. Required mostly for stone setting classes to hold the ring shank.
- Ring Mandrel, Steel
  Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.
- Ring Sizer
  Optional, used to measure your ring size. Several sets will be provided to share in class.
- Soldering Kit
  
  (Optional)
  Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.
- Student Files
  Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
- Swivel Vise
  The advantage of this vise is the 360 degree swivel allowing you to brace a piece and move it in every direction. Classes requiring a vice can be any vice that may be clamped to table. Suction vices will also suffice.
- Tube Cutting Pliers
  A great gadget to aid in cutting tubes. These pliers create even leverage on the tube for sawing. Provided for all classes with tubes.
- Wood Ring Mandrel
  Used to brace rings for polishing; this will save your hands. However, I also use a wood ring mandrel for project where I have to drill into the ring, this way you do not ruin your steel ring mandrel. Wood ring mandrels will be provided to share in classes.
Intrepid
Intrepid

Level

Advanced

Session

6 hours, all day

Description

Can’t get enough rings? Lets make two more and put them together and go for extravagance. Topped with a 10mm pearl this ring will be the showcase in your jewelry box.
Tools
Some tools will be provided by the instructor. Please refer to your registration.
- Bench Block
  Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
- Bench Pin
  There are a variety of bench pins available on the market, any will do. However, you will need to bring a 4” or larger C-clamp. As the C-clamp provided with a bench pin does not fit most tables at the shows.
- C-clamp
  To be used with bench pins to clamp to tables. May be found at any local hardware store. Must be at least 3 inches.
- Cut Lube
  Used to lubricate saw blades and drill bits for ease of cutting.
- Flex shaft
  Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited.
- Hand Tools
  
  Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.
  
  Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
  
  Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
  
  Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
- Heavy Duty Cutters
  Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.
- Horned Anvil
  For most classes using this anvil, the key is in the square side. We will use to assist in the forging of the shape.
- Jeweler’s Saw
  Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
- Magnifier or Optivisor
  – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.
- Muslin buffing wheels
  Used with a flex shaft or Dremel to polish metal.
- Ott Light or Task Lamp
  This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
- Rawhide/Leather Mallet
  Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubberone may not.
- Ring Mandrel, Steel
  Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.
- Ring Sizer
  Optional, used to measure your ring size. Several sets will be provided to share in class.
- Round File
  Used to file curved areas. Round files are gradually tapered, cut and workable to the point. Used where it is necessary to enlarge a hole or round off a radius.
- Soldering Kit
  
  (Optional)
  Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.
- Student Files
  Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
- Tube Cutting Pliers
  A great gadget to aid in cutting tubes. These pliers create even leverage on the tube for sawing. Provided for all classes with tubes.
Tapered Bezels
Tapered Bezels

Level

Advance

Session

6 hours, all day

Description

This fabricating class will touch on multiple skills that can be used to enhance any smithing project. Create a contemporary ring while refining your sawing, shaping and soldering techniques. Students will be encouraged to create their own designs. If you are looking to challenge this class will surely impress. Every step will refine your skills and give you experience with that tool (saw) you have been avoiding.
Tools
Some tools will be provided by the instructor. Please refer to your registration.
- Bench Block
  Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.
- Bezel Rocker
  There are 2 bezel rockers on the market, the one shown is preferred, but if you own the other one it will work also. I usually have 2 to share at the shows.
- Bezel Shears
  Used to cut metal sheet. There are many available on the market, any of which will work, however they should NOT be serrated. (Tin snips or airplane shears will also work, however, they may be large and cumbersome.) If the project has curves in the design and you own a pair, bring curved bezel shears. This is an optional item for most classes. Shears will be provided for use during classes.
- Curved Burnisher
  
  Used to burnish or smooth the surface of metal. For most projects using this tool you will want at least a 3mm ball. This tool may also be found at your local craft store for use with clay or nail art.
- Flex shaft
  Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited.
- Hand Tools
  
  Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.
  
  Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
  
  Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
  
  Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
- Magnifier or Optivisor
  – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.
- Muslin buffing wheels
  Used with a flex shaft or Dremel to polish metal.
- Ott Light or Task Lamp
  This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
- Rawhide/Leather Mallet
  Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubberone may not.
- Ring Mandrel, Steel
  Used for shaping and forming metal into rings. A plastic one will not work in its place. Instructor will provide to share (1 for every 2 people) for every class needed.
- Ring Sizer
  Optional, used to measure your ring size. Several sets will be provided to share in class.
- Soldering Kit
  
  (Optional)
  Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.
- Student Files
  Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.